TAG:
 点击浏览该文件1. Motion-JPEG Images Request Remark: Request a multipart JPEG image stream. ServerPush is recommended. Parameter: Image Size QCIF (halfsize) CIF (fullsize) 4CIF (hugesize) CCD NTSC 176 x 112 352 x 240 704 x 480 CCD PAL 176 x 144 352 x 288 704 x 576 CMOS 320 x 240 640 x 480 Camera ID : Depends on device, usually 1~4 Example:  http://cameraip/mjpg/fullsize.jpg?camera=12. DOME Settings Remark: Set/Query DOME model Parameter: DOME model : Example 1 for Lilin, 2 for Dynacolor, 3 for Sony Example: http://cameraip/setdome?domtype=1&camera=1http://cameraip/dometype&camera=13. PTZ Control Remark: Control Relative Pan/Tilt/Zoom of DOME Device. Parameter: Relative Pan: Relative Pan Degrees Relative Tilt: Relative Tilt Degrees Relative Zoom: Relative Zoom Degrees Example: http://cameraip/ptzcontrol?rpan=2&camera=1http://cameraip/ptzcontrol?rpan=3&rtilt=2&camera=1http://cameraip/ptzcontrol?rzoom=10&camera=14. Preset Settings Remark: Set/Remove/Go Preset Positions Parameter: Preset No: Preset Numbers, usually 20 Example: http://cameraip/preset?setpreset=2&camera=1http://cameraip/preset?removepreset=2&camera=1http://cameraip/preset?gopreset=2&camera=15. GPIO Control Remark: Query DI input status, Set DO output status Parameter: Example: http://cameraip/iocontrol?input=checkhttp://cameraip/iocontrol?relayon=1http://cameraip/iocontrol?relayon=06. Video Quality Settings Remark: Set/Query Contrast/Hue/Brightness/Saturation parameters Parameter: value : 1~255 Example: http://cameraip/videoquality?cmd=check&camera=1http://cameraip/videoquality?cmd=set&contrast=128&hue=128&brightness=128&saturation=128&camera=17. Video Compression Settings Remark: Set/Query Compression parameters Parameter: value : 1 (LowLow), 2 (Low), 3 (Medium), 4 (High), 5 (HighHigh) Example: http://cameraip/compression?cmd=check&camera=1http://cameraip/compression?cmd=set&compression=3&camera=18. Motion Detection Settings Remark: Set/Query Motion Detection Parameter Parameter: Frequency : Motion Frequency Sensitivity : Motion Sensitivity Example: http://cameraip/MD?cmd=check&camera=1http://cameraip/MD?cmd=set&frequency=50&sensitivity=80&camera=19. Motion Detection Block Settings Remark: Set/Query Motion Detection Blocks Parameter: Block No : Motion Detection Block Number, usually 11 (width) x 7 (height), so block no could be 1~77 Example: http://cameraip/MDBlock?cmd=check&camera=1http://cameraip/MDBlock?cmd=set&blockno=1,5,10,20,75&camera=110. Device Password Settings Remark: Set/Update/Delete Username/Password Parameter: UserName Password Example: http://cameraip/setusers?cmd=set&username=root&password=passhttp://cameraip/setusers?cmd=update&username=root&password=unisvrhttp://cameraip/setusers?cmd=remove&username=root11. Device Event Script Settings Remark: Set Event Scripts into device Parameter: Event Trigger: (1) GPIO input 1~4 (2) Motion Detection 1~4 Event Action: (1) Alert Message to specified IP & Port (2) Directly Set Relay On/Off (3) Set Relay On/Off with xx Seconds Delay Example: (1) http://cameraip/setscript?scripts=SCRIPT(2) ftp://cameraip/scriptfile.txt12. Disable Timestamp on Requested Images Remark: Use UniArgus Timestamp Instead of Device Timestamp on Top-Left corner of Images Parameter: Example: http://cameraip/timestamp=0&camera=113. Restart Device Remark: Restart device Parameter: Example: http://cameraip/restart
(iwgh) |